Replacing Lock on uPVC Door
To replace the lock, you need to first remove the handle and screw holes. This is typically simple to do.
Then, locate the screw that holds in the barrel of the lock. This is usually colored differently than the other screws and is located at the top of the lock faceplate.
Take the Cylinder off
The first step in changing the lock on a door made of upvc is to remove the existing cylinder from the door. This is a simple process that can take about 30 minutes. All you require is an screwdriver. The Euro Cylinder screw is normally located on the inside of the door, next to the lock cylinder. The screw is usually colored differently from the rest of the screws and is easy to identify. Take it off and store it in a safe location.
Once the cylinder is removed, you can start working on removing the handle. To do this, you will have to open the door wide enough so that you can see the inside of the door, as well as the faceplate of the lock.
Remove the screw that holds the handle to the door using the screwdriver. After the screw is removed you can pull the handle towards you, and then the rest out of the door.
If you're having difficulty taking the handle off, you may need to take off the screw that is holding it to the stud of the door frame. This can be done with a screwdriver or drill and you will need to be careful not to strip the screw head or cross-thread it.
If you are about to replace your cylinder, make sure that it's the right size for the door you have. Cylinders are measured using two factors: (a), the distance from the center of the Fixing Screw to the bottom of the cylinder, and (b), the distance between the hole of the keyhole and edge of the lockplate.
Take the handle off
If your door handle made of upvc becomes stiff, loose or floppy The good news is that this is a fairly simple problem to repair. The cause is usually down to wear and tear on the cylinder or internal parts of the multipoint lock, which are inside the door between the handle and the frame. It is not uncommon for Upvc locks to wear out due to extreme weather conditions, heavy use or simply ageing and this will often lead to problems with the locking or closing mechanism of the door.
If the cylinder has worn, it will often be difficult to turn the key and the lock can be stiff, which can cause the handle to drop. The cylinder can be easily repaired, and is a simple process. This can be done by yourself, however you will need to have some knowledge about the mechanism's workings. The first step is to unhook the handle that will allow you to access the cylinder and replace it with a new one.
To accomplish this, you'll need an screwdriver and tape measure. You must know the dimensions of your current cylinder because it will allow you in locating an appropriate replacement. The cylinder allows you to lock the door of your upvc. It is important that you order a replacement that is identical in size.
To get rid of the old cylinder you must remove the screws that are holding it. You should be cautious not to pull out the screws, as this could make it difficult to remove the screws in the future. After the screws have been removed, the cylinder will come out easily.
Remove the Lock Barrel
Upvc is a strong material, designed to ensure that you and your family are secure. They are available in various styles and colors that will fit any decor. They are also maintenance-free and thermally efficient. They do not come without a few disadvantages. The locking point, also known as a barrel lock, may get faulty over time and must be replaced. It's a straightforward process however, you must be aware of a few points before you begin.
You will need to remove the door handle in order to access the screw that holds the lock cylinder. The screw is usually different in color from other screws and is found near the keyhole on the edge of your door. Remove this screw and place it in a safe location. Next, carefully slide out the door's outside and inside handles. Do not rush because this could harm the uPVC.
After you have removed the handles using a screwdriver, remove the screws that attach them to the door frame. This will give you better access to the pins holding the cylinder. You can then wiggle and tug the cylinder in order to see if this helps loosen it. When it is loose, pull it towards you, and then pull it out of the socket.
After removing the old cylinder lock, it is crucial to replace it with a new one which has anti-snap protection and anti-bump. You can do this yourself if have the right tools, or you can hire an expert locksmith to do it for you. This is an easy job that shouldn't take more than five minutes.
Install the New Cylinder
A door lock made of upvc could be damaged or broken in a variety of ways, for instance, a tenant might have moved out but did not return the key, or the cylinder might have been damaged and cannot function as it should. It is essential to select the right size replacement for your upvc door lock. This is because if the incorrect one is installed it could lead to your upvc door being more vulnerable to a process known as 'lock snapping' which is the reason for 25 per cent of burglaries.
To avoid this, it is essential that the correct cylinder is used and the process to do so is relatively easy and takes only five minutes. To swap the cylinder and handle faceplate it is necessary to remove the screws that are attached to them.
Before you begin ensure that the handle is opened and that you have full access to the inside edging of the door and the handle's faceplate that holds the lock cylinder. This will ensure that you are able to easily detach the lock cylinder without needing to move the door handle and expose any internal parts of the handle frame.
Next, remove the old cylindrical device and take a measurement of it. You will need to know the length of the cylinder and the measurement of the cylinder which is used to lock or unlock the door. This will enable you to find a new cylinder that is the same or smaller. This is the most crucial part of the whole process. A cylinder should be flush with the handle backplate and have no more than 5mm protruding from it.
Install the Handle
It is not uncommon for a upvc door lock to become jammed and this can be caused by something breaking inside the case which controls the bolts that retract into the strike or keep plate. Most of the time, this issue can be solved by making an Allan key adjustment underneath the hinges of the door, however occasionally this could put too much pressure on components inside the central case and it is better to seek the help of a professional.
When changing the handle, it is essential to have easy and quick access to both sides of the handle and having the proper tools. replacing window locks is also an excellent idea to prop the door open so that it doesn't close during the process.
The first step is to loosen the screws holding the handle with the help of a screwdriver. Once these screws are loose the handle can then be removed. After the handle and cylinder are removed, it's time to install the new handle. Make sure that the new handle fits your existing center of the cylinder and cylinder. Examine the length of the spindle on the lever you have to determine this. Also, ensure that the screw fixing centres on the handle are the same as the screw fixing centres on the existing cylindrical cylinder and hole centre.
Replacement handles from Fab & Fixed are available in various styles and are built to last. These handles are ideal for those looking to improve their upvc handle and improve home security. The right handle will ensure that your house is safe and secure and will not be easy for thieves to break into.